收藏本站
NKA Series
Isolated Sub-Miniature 1W Dual Output DC/DC Converters
OUTPUT CHARACTERISTICS
Parameter
Rated Power 1
Conditions
T A =-40 °C to 120 °C
Min.
Typ.
Max.
1
Units
W
Voltage Set Point Accuracy
See tolerance envelope
Line regulation
Load Regulation 2
Ripple and Noise
High V IN to low V IN
10% load to rated load, 0312 & 0315
10% load to rated load, 3.3V output types
10% load to rated load, 5V output types
10% load to rated load, 9V output types
10% load to rated load, 12V output types
10% load to rated load, 15V output types
BW=DC to 20MHz, 0312 & 0315
BW=DC to 20MHz, 3.3V output types
BW=DC to 20MHz, 5V output types
BW=DC to 20MHz, 9V output types
BW=DC to 20MHz, 12V output types
BW=DC to 20MHz, 15V output types
1.0
8
10
10
6.5
6
6
25
40
50
40
40
40
1.2
14
15
12
8
8.5
7
60
80
75
65
60
60
%/%
%
mV p-p
ISOLATION CHARACTERISTICS
Parameter
Conditions
Min.
Typ.
Max.
Units
Isolation test voltage
Resistance
Flash tested for 1 second
Viso= 1000VDC
3000
10
VDC
GΩ
GENERAL CHARACTERISTICS
Parameter
Switching frequency
Conditions
0303, 0305, 0312, 0315, 0503 and 0505XE
All other types
Min.
Typ.
95
120
Max.
Units
kHz
TEMPERATURE CHARACTERISTICS
Parameter
Speci?cation
Storage
Case temperature rise above
Conditions
All output types
5V output types
Min.
-40
-50
Typ.
30
Max.
85
130
Units
°C
ambient
Cooling
All other output types
Free air convection
21
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a speci?ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NKA series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no speci?c agency approvals, such as the NKA series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NKA series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While
parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically
polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We
therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from speci?ed test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
1. See Derating Graphs.
2. 12V input types have typically 3% less load regulation.
www.murata-ps.com/support
KDC_NKA.J02 Page 2 of 7
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NKE1209SC CONV DC/DC 1W 12VIN 9V SIP SGL
NLC322522T-221K INDUCTOR 220UH 10% 322522
NLC565050T-1R5K-PF INDUCTOR POWER 1.5UH 1.6A 2220
NLFC453232T-680K-PF INDUCTOR SHIELD 68UH 10% 1812
NLJT476M006R1600 CAP NIOB OXIDE 47UF 6.3V 1210
NLW250-25 CAP ALUM 250UF 25V AXIAL
NMA0509SC CONV DC/DC 1W 5VIN 9VOUT SIP DL
NMA2405SC CONV DC/DC 1W 24VIN 5VOUT SIP DL
相关代理商/技术参数
NKA1215D 功能描述:DC/DC转换器 1W 12V to +/-15V RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NKA1215DC 功能描述:DC/DC转换器 1W 12V to +/-15V Dual Output RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NKA1215S 功能描述:DC/DC转换器 1W DUAL OUT 12-15V RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NKA1215SC 功能描述:DC/DC转换器 1W DUAL OUT 12-15V Dual Output RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NKA1215SC 制造商:Murata Power Solutions 功能描述:DC-DC CONVERTER
NK-A12-32S-A150 制造商: 功能描述: 制造商:undefined 功能描述:
NKA131SB 制造商:Stanley Electric Co 功能描述:Displays Module 1DIGIT 8LED Orange CC 10-Pin PDIP Tray
NKA131S-B 制造商:Stanley Electric 功能描述:Indicator,LED